About the project

Process simulation should be reachable, accessible, and teachable.

ALSIMU is a browser-based P&ID simulator built for the people who actually need one — students, apprentices, junior field technicians, and engineers taking their first steps into a process plant. It opens in a single page on a phone or a laptop, without the licence fees and multi-seat contracts that put other simulators out of reach. Just visit alsimu.com and start building.

Why ALSIMU exists

A short answer to a long-standing problem.

Walk into any process-engineering classroom, any control-room training centre, any vocational school, and you will find the same tool: a commercial P&ID simulator. They are excellent. They are also expensive, locked behind multi-seat licences, and rarely reachable by the very people who need them most — students, apprentices, and technicians at the start of their career.

A junior technician should not have to wait for a plant to be built in order to learn how a PSV protects a pump from deadheading.

The gap is real, and it is not a small one. Most process-safety incidents in the field are traced back to misunderstandings of the line-up: a valve left closed, a check valve installed backwards, a suction line that was never designed to run dry. These are not exotic failure modes. They are the everyday shapes of the mistakes that a good simulator lets a student make a hundred times before they ever set foot on a real unit.

ALSIMU was built to close that gap. It is a complete, honest P&ID simulator: valves, pumps, compressors, vessels, columns, relief devices, PID loops, VFDs, heat exchangers, ISA instruments, a design-review engine that audits a drawing the way an experienced engineer would, and a 3D walkthrough of the whole plant. It runs in the browser at alsimu.com, saves to a single file, and is bilingual (English / French). It is built to be readable, so that anyone — a student, a teacher, a curious technician — can open it and understand what is happening inside.

Who built this

ALSIMU is the work of one engineer, built from experience on both sides of the control room.

Boulingui Bouka Georges Loyde

Instrumentation & Control Engineer

I am an Instrumentation and Control Engineer based in Libreville, Gabon. I studied at Regent University of Science and Technology in Accra, Ghana, where I earned a Bachelor of Engineering in Instrumentation Engineering. My work today sits at the junction of the field and the control room: supervising SCADA systems, coordinating with operations, and translating what the instruments are telling us into decisions that keep a plant running safely.

Before and alongside that, I spent years teaching — fundamental electronics, robotics, and applied artificial intelligence — to students and technicians just starting out. That teaching experience is where ALSIMU began. I kept seeing the same problem: the people who needed to practise on a P&ID diagram were the ones who could least afford the tools that let them do it. So I built one, from scratch, in a browser, with the same physics I work with every day.

ALSIMU is my attempt to put a serious process simulator into the hands of every student, apprentice, and junior technician who wants to learn the line-up before they ever touch a real unit.

🎓B.Eng. Instrumentation Engineering
Regent University of Science and Technology — Accra, Ghana
⚡Electrical Dispatcher
Karpowership & GESA — Libreville, Gabon
🧑‍🏫STEM & Electronics Educator
Acte Academy · Anointed Technical Training Center
📍Libreville, Gabon

Who it is for

Built for the classroom, the workshop, and the very first shift.

🎓

Students & apprentices

Practice the fundamentals of flow, pressure, level and temperature control without waiting for lab time or a shared licence.

🧑‍🔧

Field technicians

Rehearse a line-up, a deadhead scenario, or a suction-starvation event before it happens on a real unit — where the cost of a mistake is measured in downtime.

📐

Junior engineers

Sketch a P&ID, run the design review, and see immediately what an experienced reviewer would flag as unsafe or incomplete.

👩‍🏫

Teachers & trainers

Load one of the twelve built-in teaching examples, project it on a screen, and let the class operate the plant together.

🏭

Small plants & workshops

Give every operator a sandbox where they can practise a start-up sequence without touching the real control system.

🌍

Anyone, anywhere

All you need is a browser. Open alsimu.com on a phone, a tablet or a laptop, and the simulator is there.

Two honest physics models

Liquids and gases do not behave the same way, so ALSIMU does not pretend they do.

💧 Fluid mode

Liquids behave like liquids

Vessels drain by gravity through open lines. Flow streams are drawn as thick, saturated dashes. Pumps lose suction, cavitate, and can be damaged by dry running. Elbows are real; siphons and head are felt in the routing. This is the mode you use for water treatment, IX columns, dosing skids, and any liquid transfer system.

💨 Gas mode

Gases only move when something moves them

No gravity drain. A gas only flows because a compressor, a pressure differential, or a relief event drives it. Streams are drawn as light, fast puffs — visually distinct from liquids at a glance. Compressors heat the gas as they compress it, and the receiver temperature rises as it fills. This is the mode you use for compression skids, fuel-gas systems, and vent headers.

What is inside

A deliberately complete feature set — every piece earned its place.

🛡
Design review engine An automatic safety audit that flags missing PSVs, reversed check valves, unconnected pipes, closed vessels, and unattached instruments. Blocks ▶ RUN while errors remain.
⚙️
Deadhead & starvation A running pump with a blocked outlet starts a live countdown. If a PSV is present it lifts and relieves; if not, the machine is damaged after 60 s of unprotected deadhead.
🎛
Real PID control Ki, Kp and Kd in velocity form with automatic anti-windup. Controllers can drive motor valves, VFDs, pump speed, run/stop, or heat-exchanger duty — one loop, many actuators.
🌡
Temperature, everywhere Every vessel tracks a live temperature. Heat exchangers, boilers, jackets and electric heaters modify it. Pumps add a small amount of heat; compressors add a lot.
📊
ISA-5.1 instruments Over thirty instrument types: indicators, transmitters, recorders, controllers, DCS function blocks, and level instruments with selectable mounting styles (bridle, stilling well, wet leg, dry leg).
🧊
3D walkthrough Every diagram can be visited in 3D — an industrial enclosure with a concrete slab, steel frame, ceiling lamps, and WASD walk mode on desktop and a virtual joystick on touch devices.
💾
Save, load, export Projects save to a single .pidproj file with the full simulation state. Export the diagram as SVG or PNG, or the recorded run data as Excel-friendly CSV.
📚
Teaching bank Twelve small, focused examples — one idea per diagram — each with printed teaching notes on the event log. Flow paths, control loops, deadhead and starvation demos, IX treatment, gas skids.
🌐
Bilingual Every label, log message, tooltip and menu entry is translated into English and French. The language can be switched live from the toolbar.

Getting started in five minutes

You do not need a manual. You need a blank project and one example.

Open the simulator Go to alsimu.com. The welcome dialog asks you for a project name and a mode (Fluid or Gas). Pick Fluid to start.
Load a teaching example Click Load Example in the toolbar and pick card #2 (Pump with isolation). You now have a working plant with two tanks, two hand valves and a centrifugal pump.
Press ▶ RUN The pump starts, the source tank drains, the receiver fills, and the pipe dashes animate the flow. Click any valve to open or close it.
Break something on purpose Close the discharge valve (HV-102) while the pump runs and watch the countdown. Then press Esc or Pause, delete the pump, and rebuild the line your own way.
Run the design review Click the 🛡 shield in the toolbar. Any safety finding appears in the Design Review panel. Click a finding to jump to the offending component. Fix it, and ▶ RUN is unlocked again.

Under the hood

A single page, a clean engine, and a small footprint.

Front end One HTML page, one CSS file, one JavaScript file. The 3D view is a separate module that reads the same model through a small window.ALSIMU façade.
Rendering SVG for the 2D diagram (crisp at any zoom, exportable as a vector file), and three.js for the 3D walkthrough.
Simulation core The engine block is deliberately isolated from the interface: given the node graph and a time step, it returns flow rates, pressures, levels and temperatures. That makes it predictable and easy to reason about.
Controls Velocity-form PID with automatic anti-windup and a filtered derivative. Every actuator type consumes the same 0–100 % output the way its own physics dictates.
Persistence Projects are JSON in a .pidproj file. A quick copy is also kept in the browser so an accidental refresh does not lose the diagram.
Hosting Served from alsimu.com. No account, no download, no install — the simulator is one click away.

Where this is going

A small list. Every item grows from the same foundation.

📖

More teaching examples

The teaching bank is a list, not a limit. New cards are added by writing a few lines of JavaScript — one example, one idea.

🧪

Course material

Companion worksheets, guided exercises and quizzes for classroom use — mapping directly onto the built-in examples.

🌍

More languages

The translation dictionary is a plain JavaScript object. Adding a new language is a one-file change.

🔬

Deeper physics

NPSH curves, real pump head-flow characteristics, two-phase relief events — the shape of the model is already there.

The best simulator for a student is the one they can actually open. Everything in this project is oriented toward that single idea.