ALSIMU is a browser-based P&ID simulator built for the people who actually need one — students, apprentices, junior field technicians, and engineers taking their first steps into a process plant. It opens in a single page on a phone or a laptop, without the licence fees and multi-seat contracts that put other simulators out of reach. Just visit alsimu.com and start building.
A short answer to a long-standing problem.
Walk into any process-engineering classroom, any control-room training centre, any vocational school, and you will find the same tool: a commercial P&ID simulator. They are excellent. They are also expensive, locked behind multi-seat licences, and rarely reachable by the very people who need them most — students, apprentices, and technicians at the start of their career.
The gap is real, and it is not a small one. Most process-safety incidents in the field are traced back to misunderstandings of the line-up: a valve left closed, a check valve installed backwards, a suction line that was never designed to run dry. These are not exotic failure modes. They are the everyday shapes of the mistakes that a good simulator lets a student make a hundred times before they ever set foot on a real unit.
ALSIMU was built to close that gap. It is a complete, honest P&ID simulator: valves, pumps, compressors, vessels, columns, relief devices, PID loops, VFDs, heat exchangers, ISA instruments, a design-review engine that audits a drawing the way an experienced engineer would, and a 3D walkthrough of the whole plant. It runs in the browser at alsimu.com, saves to a single file, and is bilingual (English / French). It is built to be readable, so that anyone — a student, a teacher, a curious technician — can open it and understand what is happening inside.
ALSIMU is the work of one engineer, built from experience on both sides of the control room.
Built for the classroom, the workshop, and the very first shift.
Practice the fundamentals of flow, pressure, level and temperature control without waiting for lab time or a shared licence.
Rehearse a line-up, a deadhead scenario, or a suction-starvation event before it happens on a real unit — where the cost of a mistake is measured in downtime.
Sketch a P&ID, run the design review, and see immediately what an experienced reviewer would flag as unsafe or incomplete.
Load one of the twelve built-in teaching examples, project it on a screen, and let the class operate the plant together.
Give every operator a sandbox where they can practise a start-up sequence without touching the real control system.
All you need is a browser. Open alsimu.com on a phone, a tablet or a laptop, and the simulator is there.
Liquids and gases do not behave the same way, so ALSIMU does not pretend they do.
Vessels drain by gravity through open lines. Flow streams are drawn as thick, saturated dashes. Pumps lose suction, cavitate, and can be damaged by dry running. Elbows are real; siphons and head are felt in the routing. This is the mode you use for water treatment, IX columns, dosing skids, and any liquid transfer system.
No gravity drain. A gas only flows because a compressor, a pressure differential, or a relief event drives it. Streams are drawn as light, fast puffs — visually distinct from liquids at a glance. Compressors heat the gas as they compress it, and the receiver temperature rises as it fills. This is the mode you use for compression skids, fuel-gas systems, and vent headers.
A deliberately complete feature set — every piece earned its place.
.pidproj file with the full
simulation state. Export the diagram as SVG or PNG, or the recorded run
data as Excel-friendly CSV.You do not need a manual. You need a blank project and one example.
A single page, a clean engine, and a small footprint.
| Front end | One HTML page, one CSS file, one JavaScript file. The 3D view is a
separate module that reads the same model through a small
window.ALSIMU façade. |
| Rendering | SVG for the 2D diagram (crisp at any zoom, exportable as a vector
file), and three.js for the 3D walkthrough. |
| Simulation core | The engine block is deliberately isolated from the interface: given the node graph and a time step, it returns flow rates, pressures, levels and temperatures. That makes it predictable and easy to reason about. |
| Controls | Velocity-form PID with automatic anti-windup and a filtered derivative. Every actuator type consumes the same 0–100 % output the way its own physics dictates. |
| Persistence | Projects are JSON in a .pidproj file. A quick copy is
also kept in the browser so an accidental refresh does not lose the
diagram. |
| Hosting | Served from alsimu.com. No account, no download, no install — the simulator is one click away. |
A small list. Every item grows from the same foundation.
The teaching bank is a list, not a limit. New cards are added by writing a few lines of JavaScript — one example, one idea.
Companion worksheets, guided exercises and quizzes for classroom use — mapping directly onto the built-in examples.
The translation dictionary is a plain JavaScript object. Adding a new language is a one-file change.
NPSH curves, real pump head-flow characteristics, two-phase relief events — the shape of the model is already there.
The best simulator for a student is the one they can actually open. Everything in this project is oriented toward that single idea.